求助Linux大神：Z690主板通过 ASM1064 扩展出的 SATA 口在 Ubuntu 下不工作
本帖最后由 itd 于 2024-6-2 11:26 编辑WIN11 和 Ubuntu 22.04 双系统
主板是 映泰Z690GTA，带8个SATA口，其中4个是原生，另外4个是通过ASM1064扩展出来的。
八口插满盘，BIOS 和 Win11 都能正常识别，但 Ubuntu 里只能识别4个原生 SATA 口上的盘。
本人 Linux 小白，搜索了下用 LSPCI 命令看到如下图，ASM1064 驱动应该是已经装上了吧，
扫描，重启，都不好使，不知道还有其他什么能做的。
谢谢大家。
驱动有没有加载，用 lspci -vvv 看。 9283684 发表于 2024-6-2 11:49
驱动有没有加载，用 lspci -vvv 看。
谢谢，用这个命令看了下，有两项相关的输出，如下截图
第一张图应该是说原生的sata，第二张就是asm1064，
不懂这样显示驱动是不是已经算是加载了呢
本帖最后由 9283684 于 2024-6-2 19:51 编辑
你这是已经驱动了，用的 ahci 驱动。用 ls -l /dev/disk/by-id (这个会显示硬盘序列号) 或者 ls -l /dev/disk/by-path 看看有没有列出所有的盘。如果没有，看看 dmesg 有没有什么错误信息。 9283684 发表于 2024-6-2 19:48
你这是已经驱动了，用的 ahci 驱动。用 ls -l /dev/disk/by-id (这个会显示硬盘序列号) 或者 ls -l /dev/di ...
ls 没有列出扩展sata口上的盘，dmesg 输出的信息太多了，我清空之后重启了电脑，
把跟硬盘相关的部分拷出来贴在下面了，可以看到原生sata口的四个盘都列出来了，
扩展口似乎也识别了，但没列出详细的硬盘信息，这部分也没有那种红字报错。
麻烦大佬有时间的话帮忙喽一眼，我也找一下其中的可疑信息到网上搜搜看。
[ 0.897368] intel-lpss 0000:00:15.0: enabling device (0004 -> 0006)
[ 0.897640] idma64 idma64.0: Found Intel integrated DMA 64-bit
[ 0.899539] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf0 impl SATA mode
[ 0.899541] ahci 0000:00:17.0: flags: 64bit ncq sntf led clo only pio slum part ems deso sadm sds
[ 0.905619] nvme nvme0: bad crto:0 cap:8202020ff0103ff
[ 0.906507] r8169 0000:06:00.0 eth0: RTL8125B, f4:b5:20:45:9f:b9, XID 641, IRQ 133
[ 0.906510] r8169 0000:06:00.0 eth0: jumbo features
[ 0.910166] nvme nvme2: Shutdown timeout set to 10 seconds
[ 0.915505] intel-lpss 0000:00:15.1: enabling device (0004 -> 0006)
[ 0.915581] nvme nvme2: 24/0/0 default/read/poll queues
[ 0.915848] idma64 idma64.1: Found Intel integrated DMA 64-bit
[ 0.919565]nvme2n1: p1 p2 p3 p4
[ 0.921716] nvme nvme0: allocated 40 MiB host memory buffer.
[ 0.931889] nvme nvme1: allocated 64 MiB host memory buffer.
[ 0.941117] scsi host0: ahci
[ 0.941240] scsi host1: ahci
[ 0.941316] scsi host2: ahci
[ 0.941381] scsi host3: ahci
[ 0.941522] scsi host4: ahci
[ 0.941645] scsi host5: ahci
[ 0.941751] scsi host6: ahci
[ 0.941837] scsi host7: ahci
[ 0.941880] ata1: DUMMY
[ 0.941881] ata2: DUMMY
[ 0.941882] ata3: DUMMY
[ 0.941883] ata4: DUMMY
[ 0.941890] ata5: SATA max UDMA/133 abar m2048@0x3b702000 port 0x3b702300 irq 129
[ 0.941895] ata6: SATA max UDMA/133 abar m2048@0x3b702000 port 0x3b702380 irq 129
[ 0.941899] ata7: SATA max UDMA/133 abar m2048@0x3b702000 port 0x3b702400 irq 129
[ 0.941904] ata8: SATA max UDMA/133 abar m2048@0x3b702000 port 0x3b702480 irq 129
[ 0.942152] ahci 0000:05:00.0: SSS flag set, parallel bus scan disabled
[ 0.952261] ahci 0000:05:00.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[ 0.952266] ahci 0000:05:00.0: flags: 64bit ncq sntf stag pm led only pio sxs deso sadm sds apst
[ 0.952917] scsi host8: ahci
[ 0.953059] scsi host9: ahci
[ 0.953206] scsi host10: ahci
[ 0.953375] scsi host11: ahci
[ 0.953448] ata9: SATA max UDMA/133 abar m8192@0x3b380000 port 0x3b380100 irq 174
[ 0.953451] ata10: SATA max UDMA/133 abar m8192@0x3b380000 port 0x3b380180 irq 174
[ 0.953454] ata11: SATA max UDMA/133 abar m8192@0x3b380000 port 0x3b380200 irq 174
[ 0.953457] ata12: SATA max UDMA/133 abar m8192@0x3b380000 port 0x3b380280 irq 174
[ 0.964732] nvme nvme0: 16/0/0 default/read/poll queues
[ 0.971069] nvme nvme1: 16/0/0 default/read/poll queues
[ 0.975682]nvme1n1: p1 p2
[ 0.995293] nvme nvme0: Ignoring bogus Namespace Identifiers
[ 1.008518]nvme0n1: p1
[ 1.148556] usb 1-3: new high-speed USB device number 2 using xhci_hcd
[ 1.254885] ata8: SATA link down (SStatus 4 SControl 300)
[ 1.254927] ata6: SATA link down (SStatus 4 SControl 300)
[ 1.254969] ata7: SATA link down (SStatus 4 SControl 300)
[ 1.255008] ata5: SATA link down (SStatus 4 SControl 300)
[ 1.266905] ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.267077] ata9.00: ATA-9: V&G SSD, Q0810B, max UDMA/133
[ 1.267130] ata9.00: 4000797360 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 1.267594] ata9.00: Features: Dev-Sleep
[ 1.268277] ata9.00: configured for UDMA/133
[ 1.268513] scsi 8:0:0:0: Direct-Access ATA V&G SSD 0B PQ: 0 ANSI: 5
[ 1.269135] sd 8:0:0:0: Attached scsi generic sg0 type 0
[ 1.269275] sd 8:0:0:0: 4000797360 512-byte logical blocks: (2.05 TB/1.86 TiB)
[ 1.269325] sd 8:0:0:0: Write Protect is off
[ 1.269333] sd 8:0:0:0: Mode Sense: 00 3a 00 00
[ 1.269374] sd 8:0:0:0: Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.269428] sd 8:0:0:0: Preferred minimum I/O size 512 bytes
[ 1.271151]sda: sda1 sda2
[ 1.271359] sd 8:0:0:0: Attached SCSI disk
[ 1.299990] usb 1-3: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=87.34
[ 1.299995] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.299998] usb 1-3: Product: USB2.1 Hub
[ 1.300001] usb 1-3: Manufacturer: GenesysLogic
[ 1.301206] hub 1-3:1.0: USB hub found
[ 1.301532] hub 1-3:1.0: 4 ports detected
[ 1.424696] usb 2-3: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[ 1.447842] usb 2-3: New USB device found, idVendor=05e3, idProduct=0625, bcdDevice=87.34
[ 1.447846] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.447848] usb 2-3: Product: USB3.2 Hub
[ 1.447850] usb 2-3: Manufacturer: GenesysLogic
[ 1.449035] hub 2-3:1.0: USB hub found
[ 1.449488] hub 2-3:1.0: 4 ports detected
[ 1.572552] usb 1-6: new low-speed USB device number 3 using xhci_hcd
[ 1.582885] ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.583025] ata10.00: ATA-9: V&G SSD, Q0810B, max UDMA/133
[ 1.583078] ata10.00: 4000797360 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 1.583525] ata10.00: Features: Dev-Sleep
[ 1.584182] ata10.00: configured for UDMA/133
[ 1.584317] scsi 9:0:0:0: Direct-Access ATA V&G SSD 0B PQ: 0 ANSI: 5
[ 1.584722] sd 9:0:0:0: Attached scsi generic sg1 type 0
[ 1.584831] sd 9:0:0:0: 4000797360 512-byte logical blocks: (2.05 TB/1.86 TiB)
[ 1.584852] sd 9:0:0:0: Write Protect is off
[ 1.584857] sd 9:0:0:0: Mode Sense: 00 3a 00 00
[ 1.584887] sd 9:0:0:0: Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.584929] sd 9:0:0:0: Preferred minimum I/O size 512 bytes
[ 1.586352]sdb: sdb1 sdb2
[ 1.586492] sd 9:0:0:0: Attached SCSI disk
[ 1.723505] usb 1-6: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00
[ 1.723509] usb 1-6: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.723511] usb 1-6: Product: USB OPTICAL MOUSE
[ 1.852551] usb 1-11: new high-speed USB device number 4 using xhci_hcd
[ 1.898863] ata11: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.899007] ata11.00: ATA-9: V&G SSD, Q0810B, max UDMA/133
[ 1.899047] ata11.00: 4000797360 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 1.899488] ata11.00: Features: Dev-Sleep
[ 1.900136] ata11.00: configured for UDMA/133
[ 1.900231] scsi 10:0:0:0: Direct-Access ATA V&G SSD 0B PQ: 0 ANSI: 5
[ 1.900514] sd 10:0:0:0: Attached scsi generic sg2 type 0
[ 1.900616] sd 10:0:0:0: 4000797360 512-byte logical blocks: (2.05 TB/1.86 TiB)
[ 1.900639] sd 10:0:0:0: Write Protect is off
[ 1.900643] sd 10:0:0:0: Mode Sense: 00 3a 00 00
[ 1.900669] sd 10:0:0:0: Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.900706] sd 10:0:0:0: Preferred minimum I/O size 512 bytes
[ 1.902199]sdc: sdc1 sdc2
[ 1.902319] sd 10:0:0:0: Attached SCSI disk
[ 2.001801] usb 1-11: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=60.90
[ 2.001806] usb 1-11: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.001809] usb 1-11: Product: USB2.0 Hub
[ 2.002833] hub 1-11:1.0: USB hub found
[ 2.003118] hub 1-11:1.0: 4 ports detected
[ 2.132550] usb 1-14: new full-speed USB device number 5 using xhci_hcd
[ 2.214907] ata12: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.215073] ata12.00: ATA-9: V&G SSD, Q0810B, max UDMA/133
[ 2.215127] ata12.00: 4000797360 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 2.215587] ata12.00: Features: Dev-Sleep
[ 2.216257] ata12.00: configured for UDMA/133
[ 2.216418] scsi 11:0:0:0: Direct-Access ATA V&G SSD 0B PQ: 0 ANSI: 5
[ 2.216781] sd 11:0:0:0: Attached scsi generic sg3 type 0
[ 2.216922] sd 11:0:0:0: 4000797360 512-byte logical blocks: (2.05 TB/1.86 TiB)
[ 2.216942] sd 11:0:0:0: Write Protect is off
[ 2.216946] sd 11:0:0:0: Mode Sense: 00 3a 00 00
[ 2.216975] sd 11:0:0:0: Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.217017] sd 11:0:0:0: Preferred minimum I/O size 512 bytes
[ 2.218532]sdd: sdd1 sdd2
[ 2.218655] sd 11:0:0:0: Attached SCSI disk
[ 2.268601] r8169 0000:06:00.0 enp6s0: renamed from eth0
[ 2.286006] usb 1-14: New USB device found, idVendor=8087, idProduct=0029, bcdDevice= 0.01
[ 2.286015] usb 1-14: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.294545] hid: raw HID events driver (C) Jiri Kosina
[ 2.298637] usbcore: registered new interface driver usbhid
[ 2.298640] usbhid: USB HID core driver
[ 2.301090] input: USB OPTICAL MOUSEas /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:275D:0BA6.0001/input/input6
[ 2.301210] hid-generic 0003:275D:0BA6.0001: input,hidraw0: USB HID v1.11 Mouse on usb-0000:00:14.0-6/input0
[ 2.390952] fbcon: Taking over console
[ 2.391063] Console: switching to colour frame buffer device 128x48
[ 2.399223] EXT4-fs (nvme2n1p4): mounted filesystem c0151370-0ffb-41fa-92da-8ada3c51687b ro with ordered data mode. Quota mode: none.
[ 2.469769] systemd: Inserted module 'autofs4'
[ 2.497749] systemd: systemd 249.11-0ubuntu3.12 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[ 2.497875] systemd: Detected architecture x86-64.
[ 2.498127] systemd: Hostname set to <newbie-Z690GTA>.
lsblk试试看 输出什么信息 内核更新到最新呢。。。
或者试试Ubuntu24？ seekong 发表于 2024-6-3 01:31
lsblk试试看 输出什么信息
这个命令昨天试过了，显示不出来扩展sata上面的盘 litel 发表于 2024-6-3 06:55
内核更新到最新呢。。。
或者试试Ubuntu24？
刚更新到了Ubuntu24，仍然没起作用。内核的话晚点我再看看。 主板BIOS升级最新呢
lsblk 看一下
楼主没有识别出物理接口，可能是扩展卡坏了，或者是OS兼容性问题。。换24.04试试？ 搜下，有说驱动加载错了。 itd 发表于 2024-6-2 22:23
ls 没有列出扩展sata口上的盘，dmesg 输出的信息太多了，我清空之后重启了电脑，
把跟硬盘相关的部分拷出 ...
[ 1.254885] ata8: SATA link down (SStatus 4 SControl 300)
[ 1.254927] ata6: SATA link down (SStatus 4 SControl 300)
[ 1.254969] ata7: SATA link down (SStatus 4 SControl 300)
[ 1.255008] ata5: SATA link down (SStatus 4 SControl 300)
这里似乎都down了?
页:
[1]