HBA 9405W-16i无法识别NVME盘

rx_78gp02a

偶然在闲鱼看到有人低价出专用线，遂购入测试，但是死活不认U.2盘。
1、线缆型号CEACENT SFF8643转SFF8639(2-2)适配94XX系列NVME ，手工测量过线序是正确的（一个8639的线分别接两个8643）。
2、9405W-16i已经刷最新的9405W_16i_Pkg_P24_SAS_SATA_NVMe_FW_BIOS_UEFI固件，使用HBA_9405W-16i_Mixed_Profile.bin混合模式。
3、测试过CD6\D4502\PM963(M2转U.2）\傲腾M10(M2转U.2），均不识别。EFI ROM和storcli64均提示没有NVME磁盘。
4、四个端口均测试过，可以识别SATA。
疑问：
三模HBA卡是否需要专门的配置才能使能NVME？？

打印信息：
root@arm:/opt/MegaRAID/storcli# ./storcli64  /c0 show all
CLI Version = 007.3404.0000.0000 April 18, 2025
Operating system = Linux 6.8.12-11-pve
Controller = 0
Status = Success
Description = None

Basics :
======
Controller = 0
Adapter Type =   SAS3616(B0)
Model = HBA 9405W-16i
Serial Number = SP00735649
Current System Date/time = 07/10/2025 14:08:39
Concurrent commands supported = 6144
SAS Address =  500605b00fe37f30
PCI Address = 00:67:00:00

Version :
=======
Firmware Package Build = 24.00.00.00
Firmware Version = 24.00.00.00
Bios Version = 09.47.00.00_24.00.00.00
NVDATA Version = 24.00.00.17
PSOC FW Version = 0x0001
PSOC Part Number = 05689
Driver Name = mpt3sas
Driver Version = 43.100.00.00

PCI Version :
===========
Vendor Id = 0x1000
Device Id = 0xD1
SubVendor Id = 0x1000
SubDevice Id = 0x3090
Host Interface = PCIE
Device Interface = PCIe-8GT/s
Bus Number = 103
Device Number = 0
Function Number = 0
Domain ID = 0

Pending Images in Flash :
=======================
Image name = No pending images

Status :
======
Controller has booted into certificate provision mode = No

Supported Adapter Operations :
============================
Support more than 8 Phys = Yes
Support Enclosure Enumeration = Yes
Support Allowed Operations = Yes
Support Multipath = Yes
Support Security = No
support EKM = No
Support Secure Boot = No
Support Platform Security = No
Support Package Stamp Mismatch Reporting = No
Support PSOC Update = Yes
Support PSOC Part Information = Yes
Support PSOC Version Information = Yes

Supported PD Operations :
=======================
Support Physical Link Speed = Yes

HwCfg :
=====
ChipRevision =  B0
BatteryFRU = N/A
Front End Port Count = 1
Backend Port Count = 21
Serial Debugger = Absent
NVRAM Size = 0KB
Flash Size = 16MB
Temperature Sensor for ROC = Present
Temperature Sensor for Controller = Absent
ROC temperature(Degree Celsius) = 49

Boot :
====
Max Drives to Spinup at One Time = 2
Maximum number of direct attached drives to spin up in 1 min = 60
Delay Among Spinup Groups (sec) = 2

Capabilities :
============
Supported Drives = SAS, SATA, NVMe
Enable JBOD = Yes
Max Parallel Commands = 6144
Max SGE Count = 128
Max Data Transfer Size = 32 sectors

Security Protocol properties :
============================
Security Protocol = None

使用的线材：

StevenG

我之前用的这款:原装博通LSI 9400-16i NVME HBA卡SAS/SATA拓展卡扩展NVME直通卡SAS3416芯片12Gb/s 05-50008-00

然后用的你截图里的数据线，把线插在c0和c1口，接u2，然后c4口接浪潮背板，在飞牛中能看到连接的u2（傲腾900p）和机械硬盘。

BIOS中得设置pcie为efi模式，好像legacy识别不到卡（具体配置等我晚上回家连ipmi看一下）

你先看看什么都不插，在bios里能不能看到直通卡，还有pcie好像不用拆分（当然拆分应该也不影响识别）

rx_78gp02a

StevenG 发表于 2025-7-10 16:03
我之前用的这款:原装博通LSI 9400-16i NVME HBA卡SAS/SATA拓展卡扩展NVME直通卡SAS3416芯片12Gb/s 05-50008 ...

看来折腾的人太少。
卡是正常的，能识别SATA和SAS，四个口都测试过了。
NVME线无论是接C0/C1还是C2/C3都没法识别NVME。
买的二手卡，原先的固件只支持SATA/SAS，后刷的MIX固件，在命令里面看也是启动NVME了。
BIOS能看到卡的信息，信息很少，NVME那一栏是0个盘

rx_78gp02a

还有一个很诡异的事情，网上找的大部分storcli命令在我的卡上提示都是不支持：
比如delet  NVSRAM    set factory defaults  等等

Controller = 0
Status = Failure
Description = Un-supported command

StevenG

rx_78gp02a 发表于 2025-7-10 16:23
看来折腾的人太少。
卡是正常的，能识别SATA和SAS，四个口都测试过了。
NVME线无论是接C0/C1还是C2/C3都 ...

那我也没办法啦，这玩意我也是折腾了一个下午，把bios的选项都试遍了，好在我买卡的那家有卖线，全套一张卡两条双口线，一千出头

rx_78gp02a

StevenG 发表于 2025-7-10 17:04
那我也没办法啦，这玩意我也是折腾了一个下午，把bios的选项都试遍了，好在我买卡的那家有卖线，全套一张 ...

感谢，从你的信息看卡是不需要任何配置的。
storcli64 很多命令报错基本也可以得到同样的信息。